How To Change Hydraulic Filter On Kubota Without Draining Oil

Kubota B-Series  -  Changing Oils and Filters
(Pictures are of a B7800, concepts use to other models)
Earlier performing whatever of the following operations, be sure that engine is stopped and has been given adequate fourth dimension to cool downwardly
Changing Engine Oil

1. Remove drain plug from bottom of the engine while engine is yet somewhat warm (allow plenty of time for engine to absurd down) to drain oil into oil pan.

2. Put drain plug dorsum in when oil has tuckered

3. Fill with new oil to the higher groove of the dipstick.

Replacing The Engine Oil Filter

1. Make sure that engine is off and has been given sufficient time to cool downward

2. Remove old oil filter

3. Apply a small-scale corporeality of engine oil to the rubber seal of the new filter

4. Tighten filter rapidly until it touches the mounting surface

5. Tighten filter an additional ½ turn

6. When a new filter is installed, engine oil typically decreases a little. Ensure that oil does not leak through the seal of the filter, and then refill oil as needed.

Irresolute Air Cleaner Principal Chemical element

1. Remove air cleaner embrace by undoing the hook and then rotating the cover clockwise to take information technology off.

2. Cleaning the filter:

   If filter simply contains dust: Accident compressed air (nether 30psi, 205kPa, 2.1kgf/cm²) from the inside of the filter to clean it.

   If filter contains carbon or oil: Soak filter in detergent for fifteen minutes, wash and rinse with water and let information technology air dry. When filter has completely dried, use a light to check for tears or holes.

3. Reinstall air cleaner cover (make certain that arrows are properly aligned).

Replace air filter yearly, or after every half-dozen^th cleaning, whichever comes first.

Also make sure evacuator valve is not blocked.

Evacuator valve should be opened one time a week, or daily when used in a dusty identify in gild to become rid of larger dust particles.

Cleaning Fuel Filter

Brand sure that you are in a clean area to exercise this service and that the fuel tank is less than half full

1. Loosen and take off filter bowl

2. Rinse filter bowl with kerosene

3. Remove filter and dip it in kerosene to rinse

4. Put filter associates back together and make certain to go along out dust and dirt

5. Drain fuel system <How to Bleed Fuel Arrangement>

Changing Transmission Fluid

1. Allow engine sufficient fourth dimension to absurd downwards

2. Remove drain plugs underneath transmission cases and drain oil into oil pan

3. Put plugs back in later oil has drained

4. Clean the manual strainer (come across "Cleaning Manual Strainer" below)

5. Fill with new Kubota Super UDT upward to the upper groove on dipstick

6. Start engine and let it run for a few minutes

7. Finish engine, check oil level, and make full as needed

Oil Capacity – 3.83 gallons (14.5 liters)

Do not use tractor right subsequently changing transmission fluid. Run the engine at medium speed for a few minutes prior to utilize

If you are unable to enhance the 3 indicate hitch past using the hydraulic control lever after long term storage or later changing transmission oil, plough steering wheel to the right and left several times in order to bleed air from system

Cleaning Transmission Strainer

1. Remove strainer

2. Completely detach strainer

3. Rinse strainer with nonflammable solvent to clean off filings

4. Reassemble and install strainer

Replacing Transmission Oil Filters

1. Take drain plugs (4) out of the bottom of the transmission cases

2. Drain oil

3. Put drain plugs back in

4. Apply a minor amount of make clean transmission oil to the rubber seal of the new filters

5. Tighten filter quickly until information technology touches the mounting surface

6. Tighten filter an additional ½ plough

7. Refill transmission oil after filters accept been replaced

8. Run engine for a few minutes, stop engine, and refill manual oil as needed

9. Check seals of filters for leaks

There are two transmission filters; both are at the same identify on the tractor, one on the left, and one on the correct.

Changing Front Axle Case Oil

1. Park tractor on stable, level surface

2. Remove correct and left drain plug and filling plug

3. Drain oil

4. Reinstall drain plugs

5. Refill oil

6. Wait ten minutes, then check and refill oil once more

7. Reinstall filling plug

Oil Capacity - 4.7 quarts

How To Change Hydraulic Filter On Kubota Without Draining Oil,

Source: https://www.messicks.com/blog/kubota-b-series-changing-oils-and-filters

Posted by: stewartzies1964.blogspot.com

Share this post